Halloween

⭐ Premium

Halloween Pumpkin Scarecrow Lollipop Holder

🎃🍭 Meet the Pumpkin Scarecrow! A spooky-cute lollipop holder with a removable hat and hidden storage. Perfect for Halloween!

👁 – ⬇ – 💬 –

Checking membership…

Premium model • Download with a paid membership • Personal use

Print Information

Category: Organization
Material: PLA
Nozzle: 0.4 mm
Layer Height: 0.20 mm
Supports: Yes
Infill: 10%
Difficulty: Intermediate
License: PixelForm Free Personal

About This Model

🎃 Halloween Pumpkin Scarecrow Lollipop Holder

Bring a playful touch of spooky autumn charm to your Halloween celebration with this adorable 3D-printable Pumpkin Scarecrow Lollipop Holder!

Combining a mischievous jack-o'-lantern face, a rustic scarecrow-inspired hat, and a straw-textured base, this creative design makes a delightful Halloween centerpiece with a practical purpose.

✨ Features:

🍭 Lollipop Display Holder – Specially designed posts around the hat's brim allow you to display colorful wrapped lollipops in a fun and eye-catching arrangement.

🎃 Jack-o'-Lantern Pumpkin – The pumpkin features expressive triangular eyes, a pointed nose, and a mischievous Halloween smile.

🌾 Scarecrow-Inspired Design – The pointed brown hat and straw-like decorative base give this pumpkin its charming harvest-season personality.

🎩 Removable Hat – The scarecrow hat can be lifted off, revealing the hollow pumpkin compartment underneath.

📦 Hidden Storage – Store extra wrapped candies, small Halloween surprises, or lightweight accessories inside the pumpkin.

🎨 Colorful Seasonal Decoration – Orange, brown, golden yellow, and black create a classic Halloween and autumn color combination.

🎃 Perfect For:

• Halloween party centerpieces
• Lollipop and candy displays
• Trick-or-treat celebrations
• Autumn and harvest decorations
• Halloween desk and shelf decor
• Seasonal gifts and party decorations

🖨️ 3D Printing:

The design features separate printable components, including the pumpkin body, removable scarecrow hat, and decorative base.

Display your favorite wrapped lollipops around the hat to complete the festive look!

Important Notes:

• Lollipops and candies are not included.
• Use individually wrapped candy only.
• Check that lollipop sticks fit the holders before use.
• PLA is not intended for direct food contact or high temperatures.

Make your Halloween celebrations sweeter with this playful pumpkin scarecrow!

Designed by PixelForm Studio.

Printing Tips

Print with the settings listed above.

How to Print Halloween Pumpkin Scarecrow Lollipop Holder

Recommended print settings, explained

Layer height (0.20 mm): 0.20 mm is the best balance of smooth curves and reasonable print time for most models. Use 0.16 mm for extra-smooth curved surfaces, or 0.24–0.28 mm for a quick draft.
Infill (10%): This piece takes some load, so strength comes mostly from walls rather than infill. Use 3–4 walls and 15–25% gyroid or grid infill.
Supports (Yes): This model needs supports for some overhangs. Tree (organic) supports usually leave the cleanest surfaces; check the slicer preview before printing and remove supports slowly with flush cutters once the print has cooled.
Walls: use at least 3 walls (perimeters) so the outer surface is solid and edges stay crisp after sanding.

Filament and material advice

PLA is listed for this model. PLA gives the crispest details and brightest colors; for a piece that is carried, pulled or worn every day, PETG lasts longer because it bends slightly instead of snapping.

Printing and post-processing tips

Wash the build plate with warm water and dish soap before printing; fingerprints are the most common cause of parts lifting.
A brim is only needed if corners start to lift; most models stick well on a clean textured or smooth PEI plate.
Let the print cool fully before removing it, then trim any brim or strings with flush cutters.
Light sanding (220, then 400 grit) smooths layer lines; a filler primer and acrylic paint give a fully finished look.

Frequently asked questions

Can I scale this model?: Yes. Scaling up is usually safe; when scaling down, check in the slicer preview that thin walls still have at least two line widths (about 0.8 mm with a 0.4 mm nozzle).
Which printers can print it?: Any FDM printer with a 0.4 mm nozzle and a build plate larger than the model. The settings on this page were chosen to work on common printers without special tuning.
Can I sell prints of this model?: Not under the default license, which covers printing for yourself, your household and gifts. To sell physical prints, contact PixelForm first for written permission. Sharing or reselling the digital files is never allowed.